Crack MCU AT89C51RD2 Eeprom

Crack MCU AT89C51RD2 Eeprom for the embedded data and flash memory for embedded program, extract the heximal file from microcontroller at89c51rd2 and then recovery original MCU functionality;

Features

80C52 Compatible

– 8051 Instruction Compatible

– Six 8-bit I/O Ports (64 Pins or 68 Pins Versions)

– Four 8-bit I/O Ports (44 Pins Version)

– Three 16-bit Timer/Counters

– 256 Bytes Scratch Pad RAM when reading microcontroller pic18f442 software

– 9 Interrupt Sources with 4 Priority Levels

Integrated Power Monitor (POR/PFD) to Supervise Internal Power Supply

ISP (In-System Programming) Using Standard VCC Power Supply

2048 Bytes Boot ROM Contains Low Level Flash Programming Routines and a Default

Serial Loader if Crack MCU

High-speed Architecture

– In Standard Mode:

40 MHz (Vcc 2.7V to 5.5V, both Internal and external code execution)

60 MHz (Vcc 4.5V to 5.5V and Internal Code execution only)

– In X2 mode (6 Clocks/machine cycle)

20 MHz (Vcc 2.7V to 5.5V, both Internal and external code execution) before Crack MCU pic18f258 software

30 MHz (Vcc 4.5V to 5.5V and Internal Code execution only)

64K Bytes On-chip Flash Program/Data Memory

– Byte and Page (128 Bytes) Erase and Write

– 100k Write Cycles

On-chip 1792 bytes Expanded RAM (XRAM)

– Software Selectable Size (0, 256, 512, 768, 1024, 1792 Bytes)

– 768 Bytes Selected at Reset for T89C51RD2 Compatibility

On-chip 2048 Bytes EEPROM Block for Data Storage (AT89C51ED2 Only)

– 100K Write Cycles

Dual Data Pointer when Crack MCU

Variable Length MOVX for Slow RAM / peripherals

Improved X2 Mode with Independent Selection for CPU and Each Peripheral

Keyboard Interrupt Interface on Port 1

SPI Interface (Master/Slave Mode)

8-bit Clock Prescaler

16-bit Programmable Counter Array

– High Speed Output

– Compare/Capture

– Pulse Width Modulator

– Watchdog Timer Capabilities

Asynchronous Port Reset

Full-duplex Enhanced UART with Dedicated Internal Baud Rate Generator

Low EMI (Inhibit ALE)

Hardware Watchdog Timer (One-time Enabled with Reset-Out), Power-off Flag

Power Control Modes: Idle Mode, Power-down Mode

Single Range Power Supply: 2.7V to 5.5V

Industrial Temperature Range (-40 to +85°C)

Packages: PLCC44, VQFP44, PLCC68, VQFP64, PDIL40

AT89C51RD2/ED2 is high performance CMOS Flash version of the 80C51 CMOS single chip 8-bit microcontroller. It contains a 64-Kbyte Flash memory block for code and for data before Crack MCU.

The 64-Kbytes Flash memory can be programmed either in parallel mode or in serial mode with the ISP capability or with software. The programming voltage is internally generated from the standard VCC pin.

The AT89C51RD2/ED2 retains all of the features of the Atmel 80C52 with 256 bytes of internal RAM, a 9-source 4-level interrupt controller and three timer/counters. The AT89C51ED2 provides 2048 bytes of EEPROM for nonvolatile data storage. In addition, the AT89C51RD2/ED2 has a Programmable Counter Array, an XRAM of 1792 bytes, a Hardware Watchdog Timer, SPI interface, Keyboard, a more versatile serial channel that facilitates multiprocessor communication (EUART) and a speed improvement mechanism (X2 Mode).

The fully static design of the AT89C51RD2/ED2 allows to reduce system power consumption by bringing the clock frequency down to any value, including DC, without loss of data .

The AT89C51RD2/ED2 has 2 software-selectable modes of reduced activity and an 8-bit clock prescaler for further reduction in power consumption. In the Idle mode the CPU is frozen while the peripherals and the interrupt system are still operating. In the Power down mode the RAM is saved and all other functions are inoperative.

The added features of the AT89C51RD2/ED2 make it more powerful for applications that need pulse width modulation, high speed I/O and counting capabilities such as alarms, motor control, corded phones, and smart card readers.